Royal Hydraulics - products

Proudly Serving These Industries...

• Industrial Machinery	• Water
• Agriculture	• Ground Support
• Mobile	• Waste
• Energy (Wind, Steam, Coal, Hydro)	• Entertainment
• Marine	• Defense

products

Supplier	Electro-Hydraulic Valves	Description	PDF
		PowrFlow™ Proportional Control Valves with On-Board Electronics Valves are preset to catalog specifications GUI (Graphic User Interface) software comes with each valve (RS232 port) Set-up screens Diagnostics screens Down loadable Five Flow Metering Options Meter IN Meter OUT Equal Metering 2:1 Metering 1.3:1 Metering Six Nominal Flow Rates from .8 GPM rated to 9 GPM rated Three spool centered conditions Industry standard 7-pin connector for power and command signals connection Fast Response All valves utilize true centering spring for failure to a safe position Hall Effect spool position sensor for closed inner loop operation Standard Mountings – NFPA and ISO Standard Standard 3-year warranty Options and Accessories 12 or 24 VDC Coil Voltages Single or Dual solenoid options Electrical and mounting Connectors Adjustable Pressure compensators Restrictive style By-Pass style Power Supplies Mounting Subplates /manifolds and inline bodies	PowrFlow™ Electro-hydraulic Proportional and Servo Control Products On-Board Electro-Hydraulic Products

		Electro-Hydraulic Proportional Relief Valves Relief valves with manual control allow you to simply regulate maximum pressure. Models with electric vent control are available in either “normally-open” or “normally-closed” configurations. Electro-hydraulic models provide remote control for infinitely variable pressure settings up to the maximum pressure. H8819 SERIES 50 GPM at 15,000 PSI (190 l/min. at 1040 bar) 75 GPM at 9,000 PSI (284 l/min. at 620 bar)	H8819 Series

		Electro-Hydraulic Remote Proportional Actuators A Remote Proportional Actuator (RPA) produces output rod displacement proportional to an electrical input signal. The RPA can be used to remotely control variable displacement pumps and motors. It can also stroke spools of large valves, throttle controls, clutches or brakes. SA SERIES 1200 lbs (5,33 kN) Output Force	SA Series

		Electro-Hydrauic Valves Features: The sensor in directional control valves is to monitor the spool position. Valves without sensor are also available in both pressure control valves and directional control valves. Open-loop types are also available. EHDFG-04 and 06: 24V DC power supply is needed. EHDFG-01, 03, 04 and 06: 0 to 5V DC command signal is needed. EHDFG-04 and 06: The spool displacement is shown as a percentage. Types: Pilot Relief Valves Pressure Control Valves Relief Valves Relieving and Reducing Valves Flow Control (and Check) Valves Flow Control and Relief Valves High Flow Series Flow Control and Relief Valves Directional and Flow Control Valves High Respones Type Directional and Flow Control Valves	Electro-hydrauic Valves

Supplier	Description	PDF

	Continental - Directional Control Valves Mounting: Sub-plate or manifold mount in D03, D05, D08, and D10 configurations, Conforming to NFPA and ANSI/ISO Standards High Flow rates D03 up to 20 GPM D05 up to 35 GPM D08 up to 150 GPM D10 up to 275 GPM Pressures up to 5000 PSI Seals – Viton Available Standard Actuator Types: solenoid, air, cam, lever, and soft-shift styles Fluids: Petroleum-base, most phosphate esters, water-based fluids (not more than 40% water) and water glycol	PowerFlow Dir Control Valve Wash Down Open Option Double Redundant Control Valves


	Pattern Directional Control Valves D03 PATTERN DIRECTIONAL CONTROL VALVES Nominal Flow: 8 gpm (30 L/min), Max Flow: 15 gpm (57 L/min) Rated Pressure: 5 000 psi (350 bar) Actuators Options include: Manual Lever; Direct Solenoid; Hydraulic Piloted; Air Piloted. Exceptionally low pressure drop. Full range of Spool types, Actuators, Electrical connections and Solenoid options. D05 – N.F.P.A. D05/ISO 05 PATTERN DIRECTIONAL CONTROL VALVES Nominal Flow: 20 gpm (76 L/min), Max Flow: 40 gpm (152 L/min) Rated Pressure: 5 000 psi (350 bar) Actuator Options include: Manual Lever; Direct Solenoid; Hydraulic Piloted; Air Piloted. Exceptionally low pressure drop. Full range of Spool types, Actuators, Electrical connections and Solenoid options. D08 – N.F.P.A. D08/ISO 08 PATTERN DIRECTIONAL CONTROL VALVES Nominal Flow: 40 gpm (151 L/min), Max Flow: 90 gpm (341 L/min) Rated Pressure: 5 000 psi (350 bar) Actuator Options include: Manual Lever; Solenoid Piloted; Hydraulic Piloted; Air Piloted. Full range of Spool types, Actuators, Electrical connections and Solenoid options.	D03 Pattern Dir Control Valve D05 Pattern Dir Control Valve D08 Pattern Dir Control Valve

	High Pressure and High Flow Valves N.F.P.A./ISO Pattern Valves HP03 (Special High Pressure Pattern) DIRECTIONAL CONTROL VALVES Nominal Flow: 5 gpm (19 L/min), Max Flow: 15 gpm (57 L/min) Rated Pressure: 10 000 psi (700 bar) Actuator Options include: Manual Lever; Direct Solenoid; Hydraulic Piloted; Air Piloted. Special mounting pattern required. Full range of Spool types, Actuators, Electrical connections and Solenoid options. HP05 – N.F.P.A. (Special High Pressure Pattern) DIRECTIONAL CONTROL VALVES Nominal Flow: 5 gpm (19 L/min), Max Flow: 25 gpm (95 L/min) Rated Pressure: 8 000 psi (560 bar) Actuator Options include: Direct Solenoid; Hydraulic Piloted; Air Piloted. Special mounting pattern required. Full range of Spool types, Actuators, Electrical connections and Solenoid options. D05H – N.F.P.A. D05/ISO 05 PATTERN (With”X” and “Y” ports for external pilot and drain) DIRECTIONAL CONTROL VALVES Nominal Flow: 30 gpm (114 L/min), Max Flow: 40 gpm (151 L/min) Rated Pressure: 5 000 psi (350 bar) Actuator Options include: Solenoid Pilot; Hydraulic Piloted; Air Piloted. Special mounting pattern required. Full range of Spool types, Actuators, Electrical connections and Solenoid options. D08H – N.F.P.A. D08/ISO 08 PATTERN DIRECTIONAL CONTROL VALVES Nominal Flow: 80 gpm (303 L/min), Max Flow: 165 gpm (625 L/min) Rated Pressure: 5 000 psi (350 bar) Actuator Options include: Direct Solenoid; Hydraulic Piloted; Air Piloted. Exceptionally low pressure drop. Wide range of Spool types, Electrical connections and Solenoid options.	HP03 HP05 D05H D08H


	Directional Valves These valve are used for shifting oil flow direction of hydraulic circuit and for actuator starting/stopping as well as the operating direction shifting of actuator. Solenoid Operated Directional Valves Solenoid Controlled Pilot Operated Directional Valves " G" Series Shockless Type Directional Valves Pilot /Manually/Mechanically Operated Directional Valves Poppet Type Directional Valves Check /Pilot Controlled Check Valves	Directional Valves

Filter Type
Return Line - Suction Filters	Off-Line Filters
Pressure Filters Change over	Suction Filters
Pressure Filters PN < 100 bar	Breather Filters
Pressure Filters PN > 100 bar	Spin-On Filters
Stainless Steel Pressure Filters	Clogging Indicators
Filter Battery	Filter elements
Specifications	Accessories

Servo Valves	Flow Control Servo Valves with Analog Interface without Integrated Electronics	PDF
G761 and 761 Series Flow Control Valve
	Rated Flow: 3.8, 9.6, 19, 38 and 62 l/min. (1, 2.5, 5, 10 & 16.5 gpm) ∆p 70 bar (1,000 psi) Rated Pressure: 310 bar (4,500 psi) Rated Signal: +/-15, 40 and 200 mA single coil Port Pattern: ISO 10372 - 04 - 04 - 0 - 92	G761 Series

G771, G772, G773, 771, 772, & 773 Series Flow Control Valve
	Rated Flow: 1.9, 3.8, 9.6, and 19 l/min. (0.5, 1, 2.5, and 5 gpm) ∆p 70 bar (1,000 psi) Rated Pressure: 210 bar (3,000 psi) Rated Signal: +/- 8.0, 15, 30, 40 and 200 mA single coil Port Pattern: Multiple options available	G77X Series 771, 772 & 773 Series

G631 and 631 Series Flow Control Valve
	Rated Flow: 3.8, 9.6, 19, 38, 57, and 76 l/min. (1, 2.5, 5, 10, 15 and 20 gpm) ∆p 70 bar (1,000 psi) Rated Pressure: 310 bar (4,500 psi) Rated Signal: +/-60 and 100 mA single coil Port Pattern: ISO 4401-05-05-0-94	G631 Series

72 Series Flow Control Valve
	Rated Flow: 100 l/min (25 gpm) to 227 l/min (60 gpm) ∆p 70 bar (1,000 psi) Rated Pressure: 310 bar (4,500 psi) Rated Signal: +/-8, 15 and 40 mA single coil Port Pattern: ISO 10372 - 06 - 05 -0 - 92	72 Series

78 Series Flow Control Valve
	Rated Flow: 76, 96, 114 and 151 l/min. (20, 25, 30, and 40 gpm) ∆p 70 bar (1,000 psi) Rated Pressure: 210 bar (3,000 psi) Rated Signal: +/- 8.0, 15, 40 and 200 mA single coil Port Pattern: Moog standard	78 Series

760 Series Flow Control Valve
	Rated Flow: 0.5, 1.9, 3.8, 9.6, 19, 38 and 57 l/min. (0.13, 0.5, 1, 2.5, 5, 10 & 15 gpm) ∆p 70 bar (1,000 psi) Rated Pressure: 210 bar (3,000 psi) normal \| 350 bar (5,000 psi) special order Rated Signal: +/- 8, 15, 30, 40, 50 and 200 mA single coil Port Pattern: ISO 10372 - 04 - 04 0 - 92	760 Series

79-100 and 79-200 Series Flow Control Valve
	Rated Flow: 114, 151, 246, 380 644, 795 and 100 l/min. (30, 40, 65, 100, 170, 210 & 270 gpm) ∆p 70 bar (1,000 psi) Rated Pressure: 210, 310, & 350 bar (3,000, 4,500, & 5,000 psi) Rated Signal: +/-30 and 80 mA single coil Port Pattern: -079-2xx & 792: PORTS: 3.12 X 2.25, 8	79 Series
Servo Valves	Flow Control Servo Valves with Fieldbus Interface	PDF
D636 and D637 Series Direct-Operated Servovalves
	Rated Flow: 5 to 100 l/min (1.3 to 26.3 gpm) @ ∆p 35 bar (500 psi) per land Maximum Flow: 180 l/min (47 gpm) Size 05 Maximum Operating Pressure: 350 bar (5,000 psi) Mounting Pattern: ISO 4401 Size 03 and 05	D636 & D637 Series

D670 Series Pilot-Operated Servovalves
	Rated Flow 30 to 1,500 l/min (8 to 395 gpm) @ ∆p 5 bar (75 psi) per land Maximum Flow Up to 3,600 l/min (~950 gpm) ISO size 10 Maximum Operating Pressure 350 bar (5,000 psi) Mounting Pattern ISO 4401 Size 05, 07, 08 and 10	D670 Series

Accessories	Description
Hardware and Accessories for Industrial Valves	Various mounting hardware, electrical mating connectors, o-ring kits and related items are available to offer flexible installation of industrial valve products.	♦ Seal kits including o-rings and o-ring kits for ports to mounting face and filter exchange ♦ Hydraulic filters and replaceable filter kits ♦ Mounting screws and bolts ♦ Flushing and connecting plates ♦ Mounting manifolds ♦ Electrical mating connectors including M8 connector, PE connectors and USB communication modules ♦ Cables including configuration, commissioning and power cables ♦ Power supplies and cables ♦ Dust protection cover ♦ Configuration software for Moog Digital Valves

Software for Servovalves and Servo-Proportional Valves with Fieldbus Interface and Digital Radial Piston Pumps	Microsoft Windows®-based software that allows a user to control and exchange data between a PC and a Moog Servovalve or Servo-Proportional Valve or a Digital Control Radial Piston Pump with a fieldbus communication interface.	Software Applications Fast and convenient commissioning of the valve Configuration and tuning of valve for optimal performance Diagnostics for troubleshooting valve to reduce downtime Setting parameters accurately for multiple valves is quicker with configuration software as you can save and reuse settings, reducing time and limiting undesirable variations Status information, set values and actual values are displayed graphical for easy monitoring of overall performance Record and visualize system parameters for data mining and comparison System Requirements for Configuring on a PC IBM-PC compatible with 133 MHz 64 MB RAM 40 MB free hard disc capacity Windows® NT/2000/XP/Vista

DIN RailModules	Moog's DIN rail mounted module analog control cards are ideal for use in enclosures where space is limited. Modules include servoamplifers, transducer conditioning electronics, command and auxilliary function modules, valve drive amplifiers, and power supplies.	Features Internal selector switches allow for custom "tailoring" to fit your system's needs Front panel trim pots allow for quick and easy setup Front panel LED's and test points aid in troubleshooting Din Rail Models G122-829-001 P-I Servoamplifier – Compact DIN Rail Housing G122-826-001 Mobile P-I Servoamplifier – Step push button for optimizing G123-814-001 Dual PWM Amplifier – Use in Low End Closed Loop Application G123-815 Buffer Amplifier – Compact, DIN rail mounting G123-816 Hex Differential Amplifier – Analog Control Cards DINrail Modules G123-817 LVDT Oscillator Demodulator – High Accuracy and Repeatability with Low Noise G123-818 Signal Conditioner – Flexible Internal Dip Switch Configuration G123-819 Ramp – Analog Signal Processing Circuit G123-820 Setpoint and Ramp Module – Auto sensing of appropriate ramp G123-821 Mini DDV Amplifier – User settable frequency response G128-808 Power Supply 24VDC- 650mA – Provides a Regulated 24VDC Output G128-809 Power Supply 24VDC - 2A – Compact DIN Rail Mounting Enclosure

Hydraulic Moog System Filters	Moog's filters maintain the fluid cleanliness level required of hard-working hydraulic systems in order to give long, trouble free life.	Moog's filters maintain the fluid cleanliness level required of hard-working hydraulic systems in order to give long, trouble free life. Using the latest filtration technology, Moog supplies high quality and reliable filters. A variety of filter sizes and filter element micron ratings are available. Optional seal materials make these filters compatible with most hydraulic fluids.

Mounting Manifolds	Various mountings manifolds are available for standard industrial valves, including base and adapter types for mounting and flushing requirements.	Various mountings manifolds are available for standard industrial valves, including base and adapter types for mounting and flushing requirements. Other hardware such as bolts and connectors are also available. The specific accessories you may need for a particular model are listed in the relevant product catalogs and can be ordered through your local office. Adjustable metering orifice (AMO) manifolds May be used to add hydraulic damping for improved dynamic performance in a servosystem The bypass orifice is incorporated into a manifold between the servovalve and the motion device Can be adjusted to set the optimum performance after final installation Base mounting manifolds Straight thread or NPT port connections for hydraulic lines Some models available in aluminum or steel Five port configurations for separate pilot supply requirements Crossport relief valve (CRV) and dual port relief valve (DRV) manifolds Available for limiting high-pressure situations caused by rapid acceleration or deceleration of an inertial load CRV’s relieve one control port to the other DRV’s relieve either control port to tank Flushing blocks Mount in place of the valve when filtering hydraulic fluid prior to use in the system Helps eliminate the possibility of servovalve contamination new system flushing or fluid replacement operations Safety auxiliary manifolds When start-up or safety requirements make it necessary to isolate the servovalve from the motion device, the sandwich manifold can be triggered electrically or hydraulically Safety manifolds can be configured to lock-up, float, or move an actuator to a desired fail-safe position

Portable Valve Testers	Valve testers are a cost effective method for evaluating valves in the field. They provide a quick and easy means of differentiating between hydraulic and electronic problems.	Valve testers are a cost effective method for evaluating valves in the field. They provide a quick and easy means of differentiating between hydraulic and electronic problems. There are five models to choose from, each with different levels of capability and flexibility to meet your specific requirements. All valve testers have a compact, easily portable design. Portable Valve Tester Models G040-119 Portable Servovalve Test Equipment G040-122 Electrical Feedback (EFB) Valve Monitor G040-123 Portable Valve Checker G040-124-001 Direct Drive Valve (DDV) Tester G040-125 Portable pQ Valve Checker M040-104 Portable Valve Test Equipment M040-120 Portable Servovalve Tester

Page 32 of 51

News from RHI

Proudly Serving These Industries...

products

Supplier

Electro-Hydraulic Valves

Description

PDF

Supplier

Description

PDF

Filter Type

Servo Valves

Flow Control Servo Valves with Analog Interface without Integrated Electronics

PDF

G761 and 761 Series Flow Control Valve

G771, G772, G773, 771, 772, & 773 Series Flow Control Valve

G631 and 631 Series Flow Control Valve

72 Series Flow Control Valve

78 Series Flow Control Valve

760 Series Flow Control Valve

79-100 and 79-200 Series Flow Control Valve

Servo Valves

Flow Control Servo Valves with Fieldbus Interface

PDF

D636 and D637 Series

Direct-Operated Servovalves

D670 Series

Pilot-Operated Servovalves

Accessories

Description